In this article below yow will discover additional incredibly good content on the subject of Installing A Bathtub.
Setting up a bathtub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is readily easily accessible, the project can move rapidly; if you have to open up a wall surface to remove the old tub as well as position the new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub and set in the new one. Make certain you have actually certified yourself for the task as well as are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed job, it is better to consider employing one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new bathtub in your bathroom if you have currently gotten a new bathtub as well as don't require to alter the setup of your previous water system pipes.
Your devices as well as product checklist need to make up the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the water system. After doing so, activate the faucets to drain any type of water remaining in the system. The procedure of getting rid of the existing taps can be quite troublesome as a result of the limited access that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a cloth ready for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been removed, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making sure that the washers are in area in between the tap and also the sink. Protect the tap in position with the maker provided backnut. As soon as the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap adapters. The former type needs to be linked to the faucet ends first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of both wooden boards under its feet, position the bathtub in the called for setting. The wooden boards are practical in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little factors.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the tub up until the level reviews degree.
To set up faucets, fit the bottom of the furthest flexible faucet port to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system as well as check all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as also examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the tub ought to wait until the bathtub has actually been utilized a minimum of once as this will certainly settle it into its last setting.
Preparing for the Installment
First of all, the supporting structure supplied with the bathroom ought to be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is important to make certain that if the tap includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets device to stop stress on the bath tub.
Fit the adaptable faucet connectors to the bottom of both taps utilizing 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to split a stiff seal, triggering the water to penetrate the wall in between the bathroom and the tiling, bring about problems with moisture and also possible leaks to the ceiling listed below.
You can select from a range of coloured sealers to blend in your components and installations. They are offered in tubes and also cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill the bath tub with water before sealing, to allow for the movement experienced when the bathtub remains in use. The sealer can split rather early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also quickly offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent reader about How to Install a Bathtub Yourself, I figured sharing that blog post was really helpful. So long as you enjoyed our blog entry kindly be sure to pass it around. I treasure reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Expert diagnostics offered.